In order to get accurate pricing for your project please submit a quote request

For your information

Pricing Structure For stencil(s) per s/f

Prices are based upon 3 factors:

  • The type of material ordered

    • Starts at

      • 3.4 mil white vinyl = $7.50 s/f (based on Lvl 1 - 4, please see below)

      • Solid Colored vinyl decals = $9.50 s/f ($2.00 increase up to level 4, please see below)
        Price subject to increase due to type of material

      • 30 mil blast resistant vinyl = $10.50 s/f ($3.00 increase up to level 4, please see below)
        $35 Set-Up Fee always applies

      • 80/20 perforated material = $14.50 s/f (this price does not change)

      • 4 mil vinyl printed color graphic with skid resistant laminate = $18.50 s/f (this price does not change)

      • Specialty materials such as sheets of heavy corrugated cardboard, 30 lbs paper-stock, and pounce paper. (please request a quote for pricing on this material)

  • The amount of detail in the design.

    • Decided by FLOORmaps design team upon review of design, this is added onto the base price if applicable

      • This increases by level:

        • Lvl 1 / $7.50 +$0 per s/f (BASIC)

        • Lvl 2 / $10.50 +$3 per s/f (SLIGHTLY INTRICATE)

        • Lvl 3 / $13.50 +$6 per s/f (MODERATELY INTRICATE)

        • Lvl 4 / $25+ +$17+ per s/f (HIGHLY INTRICATE) may not be available for blast resistant material

  • Overall sq/ft of the design

    • Discounts only apply toward 3.4 mil vinyl only

      • 1s/f to 49s/f = No discount applied to s/f price

      • 50s/f to 199s/f =10% off s/f price

      • 200s/f to 499s/f =15% off s/f price

      • 500s/f to 1499s/f = 20% off s/f price

      • 1500s/f to 4999s/f = 30% off s/f price

      • 5000+s/f subject to higher discount dependent on project detail

    • Discount may be applied to other material but is not guaranteed (Dependent on design)

DESIGN CHARGES:
Design Fees are priced $85/hr:
Pricing is subject to change without notice

This is applied to all orders that require either or;

  1. design recreation

  2. multiple design changes

  3. custom design creation

A minimum of $35 .00 up to a max of $85 per hour for design fees
Handling charges dependent on QTY of boxes shipped
Shipping varies depending on your location and is subject to change at any time.

Re-sizing of any graphics from our Design Library are subject to a set up fee ($35) only, no fee for design time will be applied unless changes to design are requested .
Set up Fee applies to all Blast Resistant designs additional to design fees.


Below are descriptions of the material we provide.

 
  3.4 mil white vinyl w/ adhesive backing  used primarily for temporary application on polished concrete or other smooth surfaces for the use of applying a variety of artistic mediums such as Solvent & Water-Based Dyes or Acid Stains topical coatings, and etching solutions. (Please do NOT use with substances like Xylene and MEK.)  Panels can be cut up to 56" wide by 10' long. Designs larger than 58" wide will be sectioned into panels connected by a .25" overlap unless otherwise specified.   *can be applied to more textured surfaces if applied correctly.  Adhesive Spray and a stippling brush are good tools to achieve correct installation. Please call for more details.

3.4 mil white vinyl w/ adhesive backing used primarily for temporary application on polished concrete or other smooth surfaces for the use of applying a variety of artistic mediums such as Solvent & Water-Based Dyes or Acid Stains topical coatings, and etching solutions. (Please do NOT use with substances like Xylene and MEK.)

Panels can be cut up to 56" wide by 10' long. Designs larger than 58" wide will be sectioned into panels connected by a .25" overlap unless otherwise specified.

*can be applied to more textured surfaces if applied correctly.
Adhesive Spray and a stippling brush are good tools to achieve correct installation. Please call for more details.

  30 mil high-tack blast resistant vinyl w/ adhesive backing  used primarily for temporary application to rough or smooth surfaces so that designs may be engraved into the surface by sandblasting or bead-blasting.  Panels can be cut up to 28" wide by 4.5' long.   *Small, intricate designs (Lvl 4 detail) may not be available in this thicker material. Thinnest detail that can be cut with this material is an 8th of an inch.

30 mil high-tack blast resistant vinyl w/ adhesive backing used primarily for temporary application to rough or smooth surfaces so that designs may be engraved into the surface by sandblasting or bead-blasting.

Panels can be cut up to 28" wide by 4.5' long.

*Small, intricate designs (Lvl 4 detail) may not be available in this thicker material. Thinnest detail that can be cut with this material is an 8th of an inch.

  6 mil black/white composite vinyl with 80/20 perforation pattern with a clear removable acrylic pressure-sensitive adhesive.   With this material we will print a custom graphic where this will then be applied to the floor surface. A clear epoxy coating will then be applied over the vinyl. The holes are close enough to give a clear image of the design and yet separate enough for the epoxy overlay to grab onto the epoxy layer underneath trapping the vinyl ensuring that there will be less risk of bubbling.  Panels will be printed up to 52" wide by 10' long with a .25" overlap on connecting panels which will need to be cut in order to lay side by side.

6 mil black/white composite vinyl with 80/20 perforation pattern with a clear removable acrylic pressure-sensitive adhesive.

With this material we will print a custom graphic where this will then be applied to the floor surface. A clear epoxy coating will then be applied over the vinyl. The holes are close enough to give a clear image of the design and yet separate enough for the epoxy overlay to grab onto the epoxy layer underneath trapping the vinyl ensuring that there will be less risk of bubbling.

Panels will be printed up to 52" wide by 10' long with a .25" overlap on connecting panels which will need to be cut in order to lay side by side.

 

Because application techniques, environmental & surface conditions vary, we cannot guarantee how the stencil design will perform under every circumstance. For this reason small 1'x1' samples of our standard 3.4 mil material , 80/20 perf material and tan 30 mil blast resistant material will be given upon request for testing purposes, we just ask that shipping is paid for.

Custom sample requests of the above material will be charged at a discounted rate. (Not to exceed 2’ x 2’)

To get your sample(s) today please submit a request.


STORAGE INFORMATION

The Pre-cut Design and the Transfer Tape that secures it are cut from adhesive-backed materials. These materials are affected by both light and heat. As long as you keep your design loosely rolled or lying flat in a cool, dark and dry place you will be able to store it up to 4 months or more. Even if you plan to use the stencil(s) within days you should avoid exposing the design to direct sunlight and heat. Heat and humidity will "activate" the adhesive. Try to install your design in a cool environment or early in the day.

If you require a stencil(s) and you wish to also have one of our artists assisted install you will receive 2 separate estimates for each service. If you require that they be together please let us know beforehand.

Assisted Installation

One of our artists will come out and assist installation with your team members. With this service you will receive 1 on 1 training. Take advantage and learn all you can. We price installation based on the jobs size, and is estimated on the amount of hours/days we feel the job will take. If the job lasts longer than estimated there will be an adjustment made on your final invoice. Minimum of 5 hours. If you are interested please request a quote today to see our availability.

We are not responsible if the area is not prepped and ready when our artist arrives. We require notice if dates are changed for the installation and we will require compensation if we are unable to refund travel costs already spent in advance.

With all installations you have the ability to have your employees trained by one of our own. 

Training Classes

$1750 a session, (does not include travel expenses)(Availability is dependent on trainers schedule. This price includes either 2 3'x3' or 1 5'x5' stencil(s) from our catalog by choice of the trainer. We will be more than happy to add your company or sponsor's company logo(s) to the training package but this will be priced separately as for any other additional stencils in which a 35% discount will be automatically added. If you are interested please request a quote today to see our availability.

consultations

$125 - 225 an hour (Dependent on project) plus travel expenses. Minimum 2 hours. One of our artists will come to your site and not only consult on the proper installation of your project but give you an individual training session. This is for those that have a feel for what they are doing but just need a push in the right direction. If you are interested please request a quote today to see our availability.

Payment Terms

Once your estimate has been approved you will receive an invoice. In the invoice there will be a link were you can pay for the invoice either by CC or Bank Wire.

If you choose to pay by check we request that you let us know and that payment be expedited. No orders will be cut and shipped out until payment has been received unless previously arranged.

On orders over $4,000 we ask that if the full amount can not be paid upfront a 50% deposit must be made before production can begin.

If we are requested to install or consult on a design, the full stencil costs must be paid in full as well as travel expenses so that we can make all travel arrangements. Installation costs must be paid upon completion of installation.

We will be more than happy to allow payment arrangements if necessary but this is subject for approval and can not be guaranteed. Please contact us to make arrangements.

ORDERS AND CANCELLATION

FLOORMap™ Stencils are custom-sized and/or cut to order. Upon customer approval, all orders must be prepaid prior to entering the production phase for cutting. The only exception to this would be the suppliers that are set up on terms. Orders that have been processed/charged but not yet cut can be canceled. Such orders will be assessed a 20% cancellation fee on the total amount of the order prior to issuing a credit or refund. Any incurred Design Fee charges are not refundable. Orders that have been processed/charged and that have already been cut by our production department cannot be canceled and are not subject to any credit/refund options.

Limit of liability

Please read and understand the following statement. FLOORmaps™ INC. is liable for only the replacement of defective material. We cannot control the use or method of application. We are not responsible for any claims, liability or damage(s) related to the use of this product either by mistakes in application, reactions of applied chemical products, environmental or structural conditions, surface conditions or misuse by consumer. We cannot guarantee that every structural surface or applied medium will satisfactorily work with this product. User assumes all risk and liability and is encouraged to test the compatibility of intended structural surfaces and mediums with the FLOORMaps™ before project application.